One of the drawbacks to the trike design is that most folks are not visually conditioned to seeing this format and they often strike us as unbalanced. This holds true with the Slingshot even more so due to its open rear wheel.

A little careful design work by the Corbin Wizard's and our new Fleetliner Saddlebags provide a more balanced visual while adding much needed storage. How much storage? A whopping 104 liters with both bags combined. For those not yet commited to the metric system, that equates to over three and a half cubic feet!

Corbin's Fleetliner bags were specifically designed for the Slingshot to emulate the visuals of the bike and integrate perfectly. Notice how the lines and details of the stock bodywork has been incorporated into the design of the bags and they give a more balanced aesthetic. We think the images above speak for themselves.

Fleetliner saddlebags are specially engineered for each vehicle so they fit the profile perfectly, like pieces of a puzzle. This enables the bags to carry the weight of the contents closer to the centerline and maintain a good center of gravity. Another benefit of our design and mounting system is a smaller overall width for less wind resistance. You won't even notice they're back there when riding and they remain stable at all speeds.

Because the Slingshot doesn't lean in corners, we were able to make these bags larger than our typical Fleetliner bags... approximately 50 liters per side (left saddlebag holds more than the right saddlebag for pully clearance). Since all of the saddlebag capacity runs inboard, you must take care when running a larger tire/wheel combo. The Corbin R&D team left enough clearance for a 305 series tire which is more than you can put on a stock rim. If you go with an aftermarket wheel, be sure the offset is correct so you won't face a rubbing problem with the tire on the saddlebags.

PLEASE NOTE: Due to an unexpected supply problem, we have retooled the saddlebags to use a trunk style latch as shown here. The bags now have this heavy duty single pin design but still operated on the remote release as shown.

Fleetliner doors now secure with an automotive trunk style latch which is activated via the chrome remote. Doors open to the side and are held with a small cable. In addition to the large body area of the bags, we've built a pouch into the doors to keep you smaller items easily at hand. Doors are made with thermoformed ABS for durability and a clean finish.

Both bags come fully lined to protect your cargo and are fully sealed against the weather. Installation on the Slingshot is fairly simple and Corbin supplies all required mounting brackets. Saddlebags are constructed of our roto-molded polyeurethane material and come to you prepainted. Saddlebag bodies and brackets all come painted in wrinkle black to blend with the Slingshot chassic and lower plastics. Saddlebag doors come color coordinated to your OEM paint or are available in primer ready for your custom painter's final preparation.

Included with the saddlebag set is our rear fender / splash guard that is an integral part of the setup. The fender component is a heavy duty ABS material in a mock Carbon-Fiber pattern to give it a sporty look. If you prefer, we can make the fender to match the body of the saddlebags in a matt black paint. Corbin's fender works with the license plate light transferred from you stock fender. The Corbin fender installation is a required component of the saddlebags.

With this added storage and Corbin's sport seats, the Slingshot becomes a formidable sport tourer! Remember, although our saddlebags can hold an impressive amount of gear, it is never a good idea to overload your bike. Always conform to the weight limits outlined in your owners manual to assure your safety.

Although 50 liters is quite a bit of storage, please keep in mind there are limitations in shape and door openings. In this case a standard full face helmet does not fit in the Corbin bags, but the storage area behind the seats is unaffected and will still hold a helmet.

Installation is relatively simple and does not require welding or chassis modification. One of the stock plastic underbody panels will be modified during installation with drilling and cutting template supplied. All Corbin brackets bolt to stock locations on the Polaris chassis.

Polyurethane & ABS Construction	Saddlebag bodies are manufactured of a specially designed polyurethane material for durability and a clean finish. Provides for very tight tolerances with minimal shrinkage so each part comes out true to the original design. Saddlebag doors are constructed of thermoformed ABS.
Finish	Saddlebag bodies and brackets all come prepainted in wrinkle black to coordinate with the factory plastics and underbody. Fleetliner saddlebag ABS doors come prepainted to coordinate with your OEM paint.
Saddlebag Interior	Corbin Fleetliner Bags come fully lined with a nice, thick grey liner on the inside to protect your cargo. Sure seal weather stripping around the doors keeps out the elements. Locking doors keep contents secure.

Measurements:	Capacity: Right side: 49 Liters Left side: 55 Liters
Installation:	#P-SS-BAG Installation #P-SS-BAG Panel Trim Guide
	Always carefully place items in the saddlebags, "throwing" heavy items like disk locks into the bags can create cracks in the paint on the outside.
	Corbin saddlebags will not accept a full face helmet though the storage area behind the seats is unaffected by our bags and works perfect for this.
	Be sure to specify the color and YEAR of your bike so we can color match the doors to your machine. There are variations on several colors and we require the year in order to provide the proper color.
	Sorry, but our saddlebags will not work with the Rivco trailer hitch system.
	Corbin saddlebags have been tested to work with the 305 rear tire found on the 2017 models. Minor installation changes apply to these models.
	Corbin saddles (with very few exceptions) include Genuine Leather Seating to provide a luxurious look and feel....   don't let anybody tell you that vinyl is just as good! You wouldn't buy vinyl boots would you?
	WARNING: Heater elements (when available) should never be installed in motorcycle seats that will be used by riders that cannot sense heat. This could create a hazardous condition.

* Click the Product Image to Learn More *

Storage Liners	RKA Motorcycle Luggage also offers a pair of liners for the storage areas behind the seats. You can get the full skinny on those right HERE.

Testimonials:
Comments?	Of course we want to hear from you! Have some suggestions for us or maybe comments for other riders, send them via THIS FORM.
Submit Photos:	Showcase your bike on Corbin.Com! Use this form to upload photos for possible inclusion on our website. Ready, set... LET'S SEE 'EM!
General Contacts	California Factory: Corbin Saddles 2360 Technology Parkway Hollister, CA 95023 800-538-7035 Florida Showroom: Corbin Saddles 1433 North US HWY 1 Ormond Beach, FL 32174 800-223-4332 E-Mail General Mailbox

	ITEM	DESCRIPTION	PRICE
	#P-SS-BAG	Fleetliner Saddlebag Set, Painted	$4029
	#P-SS-BAG-PRMR	Fleetliner Saddlebag Set, Primer Doors	$3920
	We do not always have a color match for all brands and model. Please enter your bike year and paint color below and we will contact you if we do not currently have the color matched. A note about paint color matching: Please Read
	Model Year
	Paint Color
	Rear Fender	Carbon-Fiber Look Fender Matt Black Painted Fender
Please be sure to select/enter all options, if applicable, before clicking the "Add To Cart" button.

       

FITMENT NOTE: Corbin products are designed to fit very close to your bike for a clean look. Due to this, other accessories or options can inhibit proper fit. As an example: Tank Consoles (dashes), ignition modules, exhaust systems, sissy bars, etc. If you have accessories installed on your bike, please let us know so we can verify the fit for you.

MILITARY & FIRST RESPONDERS: As a small token of our appreciation for your service to our country, we proudly offer a 10% discount to active military, veterans and first responders. Thank you for what you do!

CUSTOM COVERS: You are always welcome to choose from our wide variety of colors and material options for your saddle. We provide these options at no extra charge as long as we can use our existing cover patterns. Creating a new cover design requires specialized custom work and will result in additional charges.

SADDLE WARRANTY: Basepan, foam and hardware of the Corbin saddle is warranted to the original owner for life. Cover materials, Heaters, Coolers and workmanship are warranted for one year. Product will only be authorized to be shipped back for refining of shape or to replace/rectify defective parts. In cases where the rework requires a new cover, a recover charge will be applied. Cash or credit refunds are not available. All goods being handled for customer service consideration must be accompanied by a Corbin receipt and a Return Material Authorization number (RMA).

FIBERGLASS WARRANTY: Structural integrity of Corbin fiberglass components are warranted to the original owner for life. Finish and paint are warranted against manufacturing defect for one year. Damage to product and / or painted surfaces from outside forces or misuse is specifically not covered under warranty. Cash or credit refunds are not available. All goods being handled for customer service consideration must be accompanied by a Corbin receipt and a Return Material Authorization (RMA) number. A note about paint color matching, PLEASE READ

EXPORT SALES: USA pricing shown. When products are shipped throughout the world, you will see higher prices because of freight, customs, duty & applicable taxes. Please consider these costs when purchasing Corbin products outside the USA. If ordering direct from Corbin, we will compute freight charges and add them to the order. BUYER will be responsible for customs, taxes, duty or other charges.